Clik here to view.
CN0359 - RS485 connection
Hi! I have tried to connect the CN0359 with my pc using an adapter RS485-RS232 and the serial reader Putty or Realterm but I could not see any data.Can you kindly write me some indications about the...
View ArticleMore design guide about ADATE320 and ADATE209
I could get only the datasheet in the website. Is there more design guide, like tools for the register configuration,whitepaper about the mode in application, or the DMO board?Thanks!
View ArticleClik here to view.
ADN2871
Would it be possible to make ADN2871 move continuously?（CW movement like ADN2830）
View ArticleFido5x00 series Ethernet speed
Hi ADIexpertI found that some internal slides states that Fido5x00 switch can support Gbe, however only 10/100M description can be found in the datasheet , May I know which description is correct?...
View ArticleADN8810
Hi I have a question ADN8810.What is the control method for pulse drive? Best RegardsHOD
View ArticleClik here to view.
AD5522 Evaluation Board sch and pcb files
Can you convert AD5522 Evaluation Board sch and pcb files to Altium or at least convert the files from PADS binary format to PADS ASCII format ?Thanksnati
View ArticleClik here to view.
AD5522 for a simple open short tester
I want to use AD5522 to build a simple open short tester to measure the resistance of IC pins, which to support up to 5000 pins. It seems i'll need to a analog switcher to support. is there any...
View ArticleClik here to view.
Why does AD5560 not have "FI" function?
As we can see in the schematic diagram,if both SW1 and SW2 switch to B connection point, it is "FI" function.
View ArticleADP8866 Output Current for each LED channel
I am trying to match the current I observe the ADP8866 draw versus the expected current (obtained from Register Settings). There are 8 LEDs total connected to the ADP8866. 2 Blue LEDs(D1,D2: Part...
View ArticleCreating a circuit with a bluetooth chip
I would like to build a circuit that will allow for the bluetooth chip EM9304 to be turned on/off or put in/out of sleep mode via the push of a button. I am wondering how I can do this manually or if...
View ArticleHow to set EXC Voltage in CN-0359
Hi everyone,I saw in the application note of CN0359 - Conductivity Measurement System, that is possible to set the EXC voltage: in the setting panel voltage is RMS o Vpp?I need to work with a square...
View ArticleHow to use the USB-I2C/LIN-CONV-Z like a Comport?
Hello,I bought this converter, and I installed all the drivers. In the Device Manager, the converter appears like a Universal Serial Bus controller, but I need it like a Comport. Is there any way to...
View ArticleAbout ADN2841 replacement
Dear Sir, Due to it's not recommend for new design, would you kind to provide a new one for replacement which no pin compatible is fine ? Thanks.
View ArticleNeed support of ADATE320 and ADATE209
Hi I am writing for support of ADATE320 and ADATE209.In our project, ADATE320 is uesd to realize 1.6 Gbps LVDS signal adjust.Original LVDS signals comes from FPGA (Xilinx HP bank). There is my...
View ArticleClik here to view.
ADP1048 : How to directly program board setting ?
Hello,I need to program ADP1048 with a microcontroller (so without using GUI supplied by AD). To reach this goal I have two questions.- The first one is to know how can I program the information of...
View ArticleAbout the OUT1 of ADN8834
Hi All, Our users are designing circuits using the ADN8834.They do not using THERMISTOR AMPLIFIER (CHOPPER 1).In this case data sheet has been described as follows. - If Chopper 1 is left unused, tie...
View ArticleClik here to view.
about AD5522 software source code
Hi, my customer is finding AD5522 software source code..... Does it can provide ??
View ArticleI need C code for AD5522,and my Controller is STM32/GD32.
can u help me? thanks for zois.
View ArticleIBIS model requirement for ATF1508AS-10AU100 - CPLD device
Hi Experts,We are using a "CPLD" whose part number is "ATF1508AS-10AU100"I am unable to find ibis models for simulation.Could you please help me find the ibis models for the device / similar device /...
View ArticleADN8831 output noise
I am using the ADN8831 with a switching frequency of 1MHz, and an output current of around 600mA. I am finding that I get around 26mV of ripple on the output. This seems to be having an effect on the...
View Article![[TVRIP] Vertex Force [バーテックスフォース] 第01話](http://animerss.com/img/TVRIP-Vertex-Force.jpg)
