Clik here to view.
ADATE207
Hi, I would like to ask whether this part ADATE207 support boundary scan? Is it IEEE1149.1 testable? This device is having JTAG port but i am not sure whether it is IEEE1149.1 testable. I tried to...
View ArticleClik here to view.
ADCMP601 hysteresis setting resistance（Rhys） vs dispersion of hysteresis...
I’m planning a circuit using ADCMP601.A target hysteresis threshold is 30 mV ± 5 mV.When using highly precise fixed resistance sufficiently, I'd like to know data of how wide a device generates...
View ArticleClik here to view.
Request IBIS model of HMC723LP3E
Hello, My customer are considering to use HMC723LP3E in their system.So they are verifying the specification of HMC723LP3E carefully.And also they want to verify the performance of HMC723LP3E through...
View ArticleClik here to view.
ADN8833 Capacitor and Inductor Selection
Please advise me again.I read a ADN8833 datasheet. (Rev. A | Page 18 of 23)Recommended capacitors is 10μF.>A 10 μF ceramic capacitor rated at 10 V is the minimum recommended value. >Increasing...
View ArticleClik here to view.
ad5522-output voltage is a Sine wave when Fin is a constant
Dear Sir/Madam. I am using a extent range. A external amplier is connected to Exfoh.output voltage is a Sine wave when Fin is a constant. The frequence is 10K Hz.VREF is confirm as 5VThe supplies is...
View ArticleClik here to view.
ADN8834 Inductors
Hi My custmer try to use ADN8834.The TEC voltage and the upper limit of the electric current are being designed by 1.0V/1.5A respectively. In DS, Recommended Inductors My custmer try to use...
View Articlemeasuring range of AD7745
Hi, what is the maximum value that the AD7745 can measure? (for example FDC1004 from TI can measure till 250 nf by having range extender circuit externally).
View ArticleClik here to view.
ADN2816: What is the latency between DataIn and DataOut?
What is the max/min/typical latency between the DataIn and DataOut Signal? Is it depending on any settings?
View ArticleClik here to view.
Question for ADN2880
Hello,I have some questions for ADN2880 from customer. Q1)Pad 4 and Pad 5 are described to connect to cathode of photo diode but the PD which the customer use can bonded just single wire. The customer...
View ArticleADP5589 Device Tree Driver
Does a device tree driver exist for the ADP5589 keyboard controller? It looks like there's a platform driver, but we're looking for a device tree driver to use in our Buildroot distribution.
View ArticleClik here to view.
ADC's with function amplitude detector
HI ROB! I DESIGNED ADC's with function amplitude detector.THESE ADC's may be apply for direct conversion receivers,power meters,,chips with adaptive signal processing.THESE...
View ArticleAD736 input amplitude for 32kHZ
I want to convert a sine voltage with frequency around 32kHz , what should i keep the amplitude of this signal to get the best conversion.I looked up the datasheet , but the input range given is around...
View ArticleClik here to view.
Inquiry on DUT pin voltage rating of ADATE318.
Dear, Would you please check the below inquiry for ADATE318? - DUT0 pin voltage ratingRelay On for HVOUT and then the DRV_LOW_LEAK line is switched off for DUT0.In case of 14V HVOUT level, it needs to...
View ArticleEvaluation board for AD538
I am looking for an evaluation board for ad538. Can you recommend an evaluation board?Or can you recommend another model and evaluation board with division capability such as ad538?
View ArticleClik here to view.
ADA2200 MS-2698
Hi I have a question ADA2200 MS-2698 Figure7. Lock-in amplifier by ADA2200. 1. How long should most suitable MasterClock be set to to measure input sinusoidal signal of 50/60Hz in figure 7.?2. A...
View ArticleClik here to view.
ADP667 latching up
Hello. I am trying to build an adjustable power supply from a 9-V alkaline battery input, using ADP667. Everything seems to work except that the 10-uF output capacitor recommended by the datasheet...
View ArticleClik here to view.
COMPSW (pin 24) on the ADN8831
Hello, I'm working with the ADN8831. We already have working component values for Thermistors and PID compensation. We had good performances with the evaluation board, however, our own board is not...
View Articlequestion of UVLO feature in ADN8831
In datasheet of ADN8831,1. The "Undervoltage Lockout" is typical 2.2V with 2.6V as maxim, there is a note about the UVLO: "The ADN8831 does not work when the supply voltage is less than UVLO." So the...
View ArticleClik here to view.
What is the best RMS-to-DC converter for 100-500 kHz range?
I'm looking for RMS-to-DC converter for 100-500 kHz range. Currently I'm choosing between AD8436 and AD637 ones. My signal source is 0.5 mH 5 Ohm coil, in which 20 mV-rms voltage is induced and I'd...
View ArticleAD7511 display
Input mode : bt1120why is that some monitors can recognize the hdmi signal from the 7511, but others can not ?
View Article